Spektrum SPM18000 DX18QQ User Manual Page 31
- Page / 74
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
31
www.spektrumrc.com
EN
Mode
You can change transmitter modes among Modes 1, 2, 3 and 4. This conver-
sion requires both a programming and a mechanical change. Please refer to
Transmitter Mode Conversion on page 61 for directions on making the necessary
mechanical changes. If mechanical changes are required for the mode you need
to change to, complete the mechanical changes fi rst, then follow the instructions
below for the software setting change.
To change the gimbal stick mode:
1. Scroll to Mode and press the scroll wheel.
2. Scroll left or right to change the gimbal stick mode. Press the scroll wheel to
save the selection.
3. Select NEXT in the lower left corner until the Calibration screen appears.
4. Move all transmitter controls to the center position and complete the calibra-
tion process before exiting the System Settings menu. See “Calibrating Your
Transmitter” for more information.
Battery Alarm
Battery Alarm enables you to change the transmitter battery type and the alarm
voltage limit. The alarm activates when the battery reaches the low voltage limit.
To change the battery alarm:
1. Scroll to the battery type and press the scroll wheel once to change the type
to LiPo or NiMH.
CAUTION: Never select NiMH when a LiPo battery is installed in the
transmitter. Doing so may over-discharge the LiPo battery and damage the
battery, transmitter or both.
2. Scroll to the battery voltage and press the scroll wheel. Turn the scroll wheel
left or right to change the voltage level. Press the scroll wheel again to save
the selection.
CAUTION: Never adjust the low voltage limit for the LiPo battery pack
below 6.4V. Doing so could over-discharge the battery pack and damage
both battery pack and transmitter.
Selecting a Language
In the Systems Settings screen, rotate the roller to highlight Language, then press
the roller to select the Language function.
Rotate the roller to select the desired Language. When the desired Language is
selected, press the roller to accept that Language. Names you input will not be
affected by language change.
Selecting a Region (EU Version)
The Region fi eld enables you to change the region of operation and power output
for transmitters sold in the European Union.
Region options include:
EU-328 FR-328
If you are using the transmitter in France, you must select
FR-328 to comply with power output regulations in France.
To change the region:
1. Scroll to Region and press the scroll wheel.
2. Scroll left or right to change the region and press the scroll wheel once to
save the selection.
Transmitters sold outside of Europe do not have the option to change the region
from US-247.
- Instruction Manual 1
- Bedienungsanleitung 1
- Manuel d’utilisation 1
- Manuale di Istruzioni 1
- SPEKTRUM DX18QQ 2
- Warranty Registration 4
- Box Contents 5
- Table of Contents 6
- Transmitter Batteries 8
- Transmitter Functions 10
- Function 11
- Main Screen 12
- Navigation 13
- Failsafe 15
- Hold Last Command 15
- Preset Failsafe 15
- SmartSafe 15
- Installation 16
- X-Plus Channels and Failsafe 18
- Installing the SD Card 19
- Model Type Programming Guide 20
- Common System Setup FunctIons 22
- Flight Mode Name Setup 23
- F-Mode Setup 23
- X-Plus Input Confi guration 24
- Channel Input Confi guration 24
- Channel Assignment 24
- Trim Setup 25
- Warnings 26
- Model Reset 26
- Model Copy 26
- Telemetry 27
- Frame Rate 28
- Prefl ight Setup 28
- Trainer 29
- System Settings 30
- Analog Switch Setup 30
- Extra Settings 32
- Serial Number 33
- Calibrate 33
- Transfer SD Card 34
- Function List 36
- D/R & Exponential 37
- Throttle Cut 38
- Throttle Curve 39
- Sequencer 41
- Range Test 42
- System Setup 43
- X-Plus Monitor 44
- ACRO (Airplane) 45
- Elevon Servo Control 46
- Flap System 47
- ACRO Mixing 47
- Acro Gyro Function 48
- Pitch Curve Function 48
- HELI (Helicopter) 49
- Swashplate 50
- Governor 51
- Tail Curve 51
- SAIL (Sailplane) 52
- Camber System 53
- SAIL Mixing 53
- Receiver Installation 54
- And Power System Requirements 54
- Specifi cations 55
- Battery Requirements 55
- Plugging in the Servos 58
- Failsafe Functions 59
- QuickConnect 60
- with Brownout Detection 60
- Storing Your System 60
- Transmitter Mode Conversion 61
- Adjust Stick Tension 62
- 2.4Ghz Troubleshooting Guide 64
- Parts list 65
- FCC Information 68
- FAA Information 69
- 1-Year LIMITED WARRANTY 70
- Parts Contact Information 72
- Declaration of Conformity 73
Related products and manuals for Control panel Spektrum SPM18000 DX18QQ
(72 pages)
(72 pages)
(47 pages)
(45 pages)
Control panel Spektrum DX7 User Manual
(108 pages)
(108 pages)
© 2020, manymanuals.com. All rights reserved. | 0.198 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals