Spektrum SPM18000 DX18QQ User Manual Page 51
- Page / 74
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
51
www.spektrumrc.com
EN
Governor
The governor function is used to set
the rotor head speed when used with
a governor installed in the helicopter.
The governor onboard will control the
engine RPM to maintain the head speed
desired. You can program values for
each switch position or fl ight mode. RPM
values can be programmed in 0.5% steps.
To Program the Governor Function:
1. Access the Governor menu option.
2. Program the RPM values by rotating the scroll wheel to the desired value.
3. Press the scroll wheel and rotate it to the desired value. Press the scroll wheel
again to save the value.
IMPORTANT: The value in the display is the corrected value. 0% is 1.5ms or
OFF for most governors. Repeat this for all governor settings.
4. Assign the output channel for the Governor. The Governor and the Gyro must
be on different channels. We recommend using AUX2 for the Governor output
channel.
5. Select a switch to control the Governor.
6. Press the BACK button to save the selections and return to the Function List.
Tail Curve
The Tail Curve function mixes tail rotor
input with the throttle/collective function
to counter torque from the main rotor
blades when using a non-heading hold
(tail lock) gyro or when using rate mode
on a gyro. See Pitch Curve for more
information on programming curves.
Mixing
Cyclic to Throttle
Cyclic-to-throttle mix prevents rpm loss
when aileron, elevator or rudder inputs
are given. This mix advances the throttle
position with cyclic or rudder control
to maintain rpm. At full throttle, Cyclic-
to-Throttle mixing prevents the throttle
from overdriving the servo.
IMPORTANT: Do not use Cyclic to throttle mix when using a governor.
To verify that the Cyclic to Throttle mix is working properly and in the correct
direction, move the fl ight mode switch to one of the active positions. Move the
programmed cyclic or rudder channel, noting the throttle position. The throttle
position should increase.
If the throttle decreases, then the opposite value (positive vs. negative) is needed.
Swashplate
The Swashplate Mix typically corrects swashplate timing issues by mixing Aileron
to Elevator and Elevator to Aileron. When adjusted correctly, the Swashplate
causes the helicopter to roll and pitch accurately with minimal interaction.
- Instruction Manual 1
- Bedienungsanleitung 1
- Manuel d’utilisation 1
- Manuale di Istruzioni 1
- SPEKTRUM DX18QQ 2
- Warranty Registration 4
- Box Contents 5
- Table of Contents 6
- Transmitter Batteries 8
- Transmitter Functions 10
- Function 11
- Main Screen 12
- Navigation 13
- Failsafe 15
- Hold Last Command 15
- Preset Failsafe 15
- SmartSafe 15
- Installation 16
- X-Plus Channels and Failsafe 18
- Installing the SD Card 19
- Model Type Programming Guide 20
- Common System Setup FunctIons 22
- Flight Mode Name Setup 23
- F-Mode Setup 23
- X-Plus Input Confi guration 24
- Channel Input Confi guration 24
- Channel Assignment 24
- Trim Setup 25
- Warnings 26
- Model Reset 26
- Model Copy 26
- Telemetry 27
- Frame Rate 28
- Prefl ight Setup 28
- Trainer 29
- System Settings 30
- Analog Switch Setup 30
- Extra Settings 32
- Serial Number 33
- Calibrate 33
- Transfer SD Card 34
- Function List 36
- D/R & Exponential 37
- Throttle Cut 38
- Throttle Curve 39
- Sequencer 41
- Range Test 42
- System Setup 43
- X-Plus Monitor 44
- ACRO (Airplane) 45
- Elevon Servo Control 46
- Flap System 47
- ACRO Mixing 47
- Acro Gyro Function 48
- Pitch Curve Function 48
- HELI (Helicopter) 49
- Swashplate 50
- Governor 51
- Tail Curve 51
- SAIL (Sailplane) 52
- Camber System 53
- SAIL Mixing 53
- Receiver Installation 54
- And Power System Requirements 54
- Specifi cations 55
- Battery Requirements 55
- Plugging in the Servos 58
- Failsafe Functions 59
- QuickConnect 60
- with Brownout Detection 60
- Storing Your System 60
- Transmitter Mode Conversion 61
- Adjust Stick Tension 62
- 2.4Ghz Troubleshooting Guide 64
- Parts list 65
- FCC Information 68
- FAA Information 69
- 1-Year LIMITED WARRANTY 70
- Parts Contact Information 72
- Declaration of Conformity 73
Related products and manuals for Control panel Spektrum SPM18000 DX18QQ
(72 pages)
(72 pages)
(47 pages)
(45 pages)
Control panel Spektrum DX7 User Manual
(108 pages)
(108 pages)
© 2020, manymanuals.com. All rights reserved. | 1.490 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals