Spektrum SPM20200 DX2.0 User Manual Page 1

2-Channel, 2-Model MemoryDSM Racing System®®

10For safe and reliable performance of your R/C model, please carefully read and follow these guidelines:1. Radio control models are not toys. They ar

11Note: When using a separate Ni-Cd receiver as a power source, the operating voltage range is 4.8–6.0V (4–5 cells) under load.Attention: Make sure th

12Note: Rubber grommets (and sometimes eyelets) are used in fuel-powered vehicles. 4FSWP-FBEX$POOFDUPS4FSWP"SN3FUBJOJOH4DSFX4FSWP

13Normal Display ScreenWhen the power switch is turned on, the LCD screen will read as shown below. This screen is referred to as the Normal Display.N

14To enter the System Mode, press both the SCROLL and CHANNEL keys at the same time while turning on the transmitter power switch. By pressing the SCR

15Model Select (System Mode)The DX2.0 has memory for two models. This feature allows for two different models to be operated with the same transmitter

16The DX2.0 allows a three-character name to be input for each of the two (2) models available. The current model, with name, will then be displayed i

17The Data Reset function allows you to reset all the programming in the selected model (1 or 2) to the factory default settings. Before using the Dat

18Next, press the SCROLL key until a beep is heard. The display will change to show the first function listed on the Function Mode flow chart as shown b

19steering and throttle servos to be increased or decreased in each direction to achieve the exact servo movement needed. The End-Point Adjustment ran

2Table of ContentsAlternate Languages ... 2Introduction...

20The Sub-Trim function of the DX2.0 is an electronic trimming feature that allows the neutral position of the servo on either the steering or throttl

21The Servo Reversing feature of the DX2.0 is a very convenient feature when setting up a new model. The purpose of the Servo Reversing function is to

22The Direct Trim Mode function of the DX2.0 is accessible through the use of the electronic throttle or steering trim levers, as well as the two elec

23The DX2.0 electronic Steering Trim lever, located just above the steering wheel, allows the center position of the servo to be manipulated in either

24The DX2.0’s electronic Throttle Trim lever, located to the left of the steering wheel, allows the center position of the servo to be manipulated in

25The Steering Dual Rate Trim Adjustment, located at Grip Lever B, allows the dual rate value (maximum servo travel) to be increased or decreased with

26The Brake End-Point Adjustment, located at Grip Lever A, allows the maximum servo travel on the braking side of the throttle trigger to be increased

27MODEL NUMBERMODEL NAMEGRIP BUTTON C O/EEND-POINTADJUSTSUB-TRIMSERVOREVERSINGTRIM VALUESGRIP LEVER BSTEERING D/RGRIPLEVER AVALUES1 2STEERING THROTTLE

28MODEL NUMBERMODEL NAMEGRIP BUTTON C O/EEND-POINTADJUSTSUB-TRIMSERVOREVERSINGTRIM VALUESGRIP LEVER BSTEERING D/RGRIPLEVER AVALUES1 2STEERING THROTTLE

29Spektrum® 1-Year Limited Warranty PeriodHorizon Hobby, Inc. guarantees this product to be free from defects in both material and workmanship for a p

3Thank you for purchasing Spectrum’s DX2.0 radio system. The DX2.0 is designed to provide R/C racers with a bulletproof 2.4GHz spread spectrum radio l

30FCC InformationThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not ca

31

© 2006 Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, Illinois 61822 (877) 504-0233 horizonhobby.com®®9290

4Servo Reversing1. With the transmitter power switch on, press the SCROLL key to enter the Function mode.2. Press the SCROLL key until “REV.NORM” app

5The DSM® system operates in the 2.4GHz band (that’s 2400MHz). This high frequency offers a significant advantage as it’s well out of the range of mode

6During the first installation, the receiver(s) must be bound to the transmitter. Binding is necessary to program the receiver(s) to distinguish its co

72. With the receiver off, press and hold the bind button on the receiver while turning on the receiver.3. Release the bind button when the LED flashes

8Steering and Throttle Trim AdjustmentSteering Servo Trim Adjustment:1. With the transmitter power switch on, move the digital steering trim lever in

AntennaPower SwitchAdjustable Steering TensionElectronic Digital Steering Trim LeverBattery cover *(8 “AA” Batteries RequiredElectronic DigitalGrip Le